Need help on compression result
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Re: Need help on compression result
27 Jul 2011 15:01
NOOOOOOOOOOOOO that not what I wanted to here.....:S
Yes I can do it but summer is too short up here in Quebec!!!!
I think I'll start ordering a few gaskets and valve...
Yes I can do it but summer is too short up here in Quebec!!!!
I think I'll start ordering a few gaskets and valve...
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Need help on compression result
27 Jul 2011 15:10
I would look at the whole top end. Rings with a valve job/ head rebuild, and possibly cam chain, or other worn components.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: Need help on compression result
28 Jul 2011 10:53
You can run it with a burnt/leaking/warped exhaust valve, but you'll probably ruin the head.
KD9JUR
Please Log in or Create an account to join the conversation.
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Re: Need help on compression result
28 Jul 2011 11:20
Thanks everyone for your advise. Guess I'll have to listen to you....
I have a spare motor and leak test and compression test had given some good result. So I'll swap it in.
Winter project is gonna be a summer project....
I have a spare motor and leak test and compression test had given some good result. So I'll swap it in.
Winter project is gonna be a summer project....
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Need help on compression result
28 Jul 2011 23:56
Having a spare motor around, now that is very handy. Do the swap and then take apart yours. Fix it as money and time allows. you might find this engine is fine and will ride good for a long time. I just got to ask, did you adjust the valves? You don't want to run with tight valves.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Re: Need help on compression result
01 Aug 2011 16:16
Motor Head. Sorry for the delay in responding. I didn't saw your reply.
Yes the valve has been ajust on the spare motor.
I've dont a cold compression test on it and it gave #1: 95psi #2: 110psi #3: 115psi #4: 115psi
The motor has been sitting for a few years. So probably a hot test would have different numbers.
Is there some precaution to do before firing the motor?
Yes the valve has been ajust on the spare motor.
I've dont a cold compression test on it and it gave #1: 95psi #2: 110psi #3: 115psi #4: 115psi
The motor has been sitting for a few years. So probably a hot test would have different numbers.
Is there some precaution to do before firing the motor?
Please Log in or Create an account to join the conversation.
- 531blackbanshee
-
- Offline
- Vendor
-

Vendors
- Posts: 7442
- Thanks: 796
Re: Need help on compression result
01 Aug 2011 21:50
a posible tight exhaust valve on your engine currently in the bike i believe is what motorhead is asking about.
an oil change and fresh plugs on your spare engine.
then just, suck squeeze bang blow
.
leon
an oil change and fresh plugs on your spare engine.
then just, suck squeeze bang blow
leon
skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
1976 kz 900 x 3
i make what i can,and save the rest!
billybiltit.blogspot.com/
www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work
kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Need help on compression result
02 Aug 2011 16:52
Actually I was attempting to get the valves looked at on the spare motor, as this seems to be what did the damage to the one in the bike. I would perform basic service to the motor before installing, and since you have a leak down tester I would do that. Check it to see what the condition is, add some oil and see if it changes, listen to where the air escapes and note the percentages.
oiling the cylinders a bit before starting would be a good Idea, also servicing the Ignition advance mechanism, maybe remove the pan and inspect/ clean.
oiling the cylinders a bit before starting would be a good Idea, also servicing the Ignition advance mechanism, maybe remove the pan and inspect/ clean.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- srosburg
-
- User
-

Public
- Thanks: 0
Re: Need help on compression result
04 Aug 2011 14:51
I'm having similar problems with my 1980 kz650. I know I have a blown ring and was planning on changing them out, and fidling with the valves. A friend had suggested that the head gasket probably needed replacing, maybe check things over real close for any signs of leaking around the head. Not a good idea to ride, you're riding with borrowed time and will need to do a engine rebuild if you try to push your luck.
Please Log in or Create an account to join the conversation.
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Re: Need help on compression result
05 Aug 2011 00:15
Open it up this night.
The problem is realy the #3 ex valve. It has a 3mm crack in it!!!
Seem to sit a little bit lower than the others. Hope it''s fixable.
I'll bring to the motor shop tomorow to have it check.
Bore are within spec. Need to check the rings and chain if they are fine.
Hope I'll have this back on the road this summer.....:dry:
The problem is realy the #3 ex valve. It has a 3mm crack in it!!!
Seem to sit a little bit lower than the others. Hope it''s fixable.
I'll bring to the motor shop tomorow to have it check.
Bore are within spec. Need to check the rings and chain if they are fine.
Hope I'll have this back on the road this summer.....:dry:
Please Log in or Create an account to join the conversation.
- elfmagic17
-
- Offline
- User
-

Registered
- Posts: 334
- Thanks: 24
Re: Need help on compression result
05 Aug 2011 00:23jcote75 wrote: I saw on a web site a method to check for burnt valve.
You hold a piece of paper at the end of exhaust pipe and if it been suck in, burnt valve. If it blow off regulary air, it's fine....
Anyone heard of this test???? seem to easy.....
This is a quick way to tell if there may be a problem but you can get a false reading if there is a exhaust leak.
Kenny Hicks
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
Please Log in or Create an account to join the conversation.
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Re: Need help on compression result
07 Aug 2011 14:20
SO I've swap motors yesterday.
Done the hot compression test on the new motor and they're all within 125psito 135psi.
Not bad for a motor that has not been running for years....
Unfortunatly, a quick look in the exhaust hole and I saw that a tip of a valve guide is broken in the new motor...... so I won't have choice to do a head job..... It does'nt seem to be burning oil right now. I'll see how it goes after a few ride.
Done the hot compression test on the new motor and they're all within 125psito 135psi.
Not bad for a motor that has not been running for years....
Unfortunatly, a quick look in the exhaust hole and I saw that a tip of a valve guide is broken in the new motor...... so I won't have choice to do a head job..... It does'nt seem to be burning oil right now. I'll see how it goes after a few ride.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
