Need help on compression result
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Need help on compression result
25 Jul 2011 19:31
HI everyone,
Would like your opinion on my compression results.
This is for a 1982 gpz1100.
The bike is running good. Sparks plug are fine except a little carbon fooling but I think this is more related to the FI ajustment. Valve we're ajust a month ago.
So I've done the test with a hot motor, no plugs and full throtle.
#1 135psi #2 135psi #3 85psi #4 130psi
Done wet test:
#1 150psi #2 150psi #3 100psi #4 145psi
So this look like a bad ring on #3 but the plug should be oil it?
Have any idea of what going on in there????
Tks for your help,
Joce
Would like your opinion on my compression results.
This is for a 1982 gpz1100.
The bike is running good. Sparks plug are fine except a little carbon fooling but I think this is more related to the FI ajustment. Valve we're ajust a month ago.
So I've done the test with a hot motor, no plugs and full throtle.
#1 135psi #2 135psi #3 85psi #4 130psi
Done wet test:
#1 150psi #2 150psi #3 100psi #4 145psi
So this look like a bad ring on #3 but the plug should be oil it?
Have any idea of what going on in there????
Tks for your help,
Joce
Please Log in or Create an account to join the conversation.
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Re: Need help on compression result
25 Jul 2011 19:56
I may add that there is no blue smoke coming from the exhaust.
There is a seapage oil leak in the front motor. Just between the cylinder and the end.
I've torque all the head nuts a month ago.
There is a seapage oil leak in the front motor. Just between the cylinder and the end.
I've torque all the head nuts a month ago.
Please Log in or Create an account to join the conversation.
- APE Jay
-
- User
-

Public
- Thanks: 0
Re: Need help on compression result
25 Jul 2011 21:43
It might be a valve. Do a leakdown. Oil should have brought it up higher than that if it was a ring.
Please Log in or Create an account to join the conversation.
- steell
-
- Offline
- User
-

Registered
- Posts: 6849
- Thanks: 208
Re: Need help on compression result
25 Jul 2011 22:36APE Jay wrote: It might be a valve. Do a leakdown. Oil should have brought it up higher than that if it was a ring.
Yep, Oil would have bumped the compression up a bunch higher if it were bad rings, like 180-200
You have valve problems
KD9JUR
The following user(s) said Thank You: wireman
Please Log in or Create an account to join the conversation.
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Re: Need help on compression result
25 Jul 2011 23:36
I've done the leak test and it look like the ex valve is leaking.
Open it up and it's at the min acceptable. at 0.05mm. Could being at them minimum acceptable leak air??? or this is looking like a bad seat or burn valve?
Open it up and it's at the min acceptable. at 0.05mm. Could being at them minimum acceptable leak air??? or this is looking like a bad seat or burn valve?
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Need help on compression result
25 Jul 2011 23:45
I hope it's a valve, not a valve seat that causing the leak!
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Need help on compression result
26 Jul 2011 00:03
You can adjust it, then run it for a couple hundred to see if it reseats some. But be ready for top end work come winter. Its called borrowed time.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- jcote75
-
Topic Author
- Offline
- User
-

Registered
- Posts: 223
- Thanks: 0
Re: Need help on compression result
26 Jul 2011 00:08
ok so I undestand that at min clearance, it should not leak
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Need help on compression result
26 Jul 2011 00:53
I'd go with maximum clearance so if the valve moves, it will have the room. Minimum clearance does not allow much for thermal expansion.....
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Need help on compression result
26 Jul 2011 02:12 - 26 Jul 2011 02:14
The oil seals go bad and leak oil down and it burns across the valve seat. Eventually, the valve doesn't close well and you lose compression.
1979 KZ-750 Twin
Last edit: 26 Jul 2011 02:14 by bountyhunter.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Need help on compression result
26 Jul 2011 02:29jcote75 wrote: ok so I understand that at min clearance, it should not leak
When performing a compression test on a cold engine, even minimal valve clearance should not influence the compression psi. Meaning clearance less than minimum spec, but not a complete lack of any clearance whatever.
The valve will seat as well as it's going to seat so long as there's some minimal clearance between the shim and the cam base circle.
Typically, minimal clearance will permit movement of the shim as opposed to where the cam base circle is pressing against the shim and holding the shim in a fixed position.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: Need help on compression result
26 Jul 2011 05:35
i tend to set exhuast valves to looser end of scale due to expansion,try reshimming #3 exhuast and see if it helps the number any
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
