Engine rebuild questions
- gwolever
-
Topic Author
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Engine rebuild questions
08 Oct 2011 11:42
So I have all the new bolts, gaskets, etc. and have updated engine with new valve seals, cam chain, guides, etc. and am now ready to put it all back together before starting on the body mods.
I have a couple of quick questions before I start though:
1. Should I use gasket sealant/cement when putting on all new gaskets? The surfaces are all cleaned and no notches or anything on them. I have heard people say I don't need gasket sealant, just to use some waterproof grease on the bottom side of the new gasket to hold it in place. Should I just use this grease method?
2. I had a couple of bolts break on me (and after $180 for an EDM removal of broken bolts and broken ez-outs) when removing valve cover, so should I use some anti-seize on all the bolts going back on the engine or not? I have heard some people actually use the blue thread lock for certain bolts on their engines? What do you guys who have done this before suggest?
Thanks for any suggestions.
I have a couple of quick questions before I start though:
1. Should I use gasket sealant/cement when putting on all new gaskets? The surfaces are all cleaned and no notches or anything on them. I have heard people say I don't need gasket sealant, just to use some waterproof grease on the bottom side of the new gasket to hold it in place. Should I just use this grease method?
2. I had a couple of bolts break on me (and after $180 for an EDM removal of broken bolts and broken ez-outs) when removing valve cover, so should I use some anti-seize on all the bolts going back on the engine or not? I have heard some people actually use the blue thread lock for certain bolts on their engines? What do you guys who have done this before suggest?
Thanks for any suggestions.
Attachment 013.JPG not found
Attachment 014_2011-10-08.JPG not found
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Engine rebuild questions
08 Oct 2011 11:57
Look at your Kawasaki factory service manual. It tells you those few spots where sealant is required, otherwise put on dry. One only area on my bike that I found the manual called for sealant is on 2 spots on the clutch cover gasket where the gasket covers the casting joints on the engine.
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Please Log in or Create an account to join the conversation.
- gwolever
-
Topic Author
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Re: Engine rebuild questions
08 Oct 2011 12:17
Cool. Thanks. I forgot to ask another question too:
Since this engine will be sitting in the garage this winter after I put it back together, what should I use to protect it from rusting internally? Or do I not have to worry about it? I have been using fogging oil on certain parts during the rebuild (cams, cylinders, pistons, etc.), so should I give the engine a good spray of fogging oil as I put her back together and not worry about rust?
And if so, which parts should I need the fogging oil for? Cylinders, cams, valves, etc?
Thanks guys.
Since this engine will be sitting in the garage this winter after I put it back together, what should I use to protect it from rusting internally? Or do I not have to worry about it? I have been using fogging oil on certain parts during the rebuild (cams, cylinders, pistons, etc.), so should I give the engine a good spray of fogging oil as I put her back together and not worry about rust?
And if so, which parts should I need the fogging oil for? Cylinders, cams, valves, etc?
Thanks guys.
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
- mark1122
-
- Offline
- User
-

Registered
- Keep twisting it
- Posts: 5297
- Thanks: 109
Re: Engine rebuild questions
08 Oct 2011 13:57
u should always oil every part as u asemble, if it is dry, and most certainly an part that will see friction.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- TeK9iNe
-
- Offline
- User
-

Registered
- What did you do!?!
- Posts: 2436
- Thanks: 28
Re: Engine rebuild questions
08 Oct 2011 14:13
Red and blue thread locker are required on many of the fasteners used during the rebuild - be sure to aquire/read your service manual during.
Before you start the engine, especially after sitting, use the starter with the kill switch off (no spark), repeatedly for 5 seconds at a time, till the oil light has gone out several times when doing this, then wait a bit before firing her up - to get lots of oil up to the head, it needs to be soaked in oil.
Good luck.
when using sealant, use it very sparingly - just a thin film applied with a finger to both surfaces is all that is required.
Before you start the engine, especially after sitting, use the starter with the kill switch off (no spark), repeatedly for 5 seconds at a time, till the oil light has gone out several times when doing this, then wait a bit before firing her up - to get lots of oil up to the head, it needs to be soaked in oil.
Good luck.
when using sealant, use it very sparingly - just a thin film applied with a finger to both surfaces is all that is required.
Motorcycle Shop Owner/Operator
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
79 Kawie Z1000 LTD
81 Kawie Z1000 CSR
83 Honda VT750C A
85 Kawie GPZ900 A2
86 Zukie GS1150 EG
93 Yamie XV1100 E
Lucky to have rolled many old bikes through my doors
Please Log in or Create an account to join the conversation.
- MFolks
-
- Offline
- User
-

Registered
- Posts: 6650
- Thanks: 541
Re: Engine rebuild questions
08 Oct 2011 15:38
This forum has seen pictures of engines assembled with excess sealing compounds oozing out of gasket surfaces, so a little goes a long ways regarding the use of these chemicals.
RTV(Room Temperature Vulcanizing) must not be used anywhere it's exposed to gasoline, as it will quickly break down and become useless in trying to seal an item.
A good,hard to find sealant is Hylomar : www.hylomar.com/index.php?option=com_con...icle&id=48&Itemid=53 Maker of several types of sealant.
If in doubt as to what type and where to apply the sealants/locking compounds, check with the shop manual. Another person to ask will be Larry Cavan at: www.cavanaughracing.com/
RTV(Room Temperature Vulcanizing) must not be used anywhere it's exposed to gasoline, as it will quickly break down and become useless in trying to seal an item.
A good,hard to find sealant is Hylomar : www.hylomar.com/index.php?option=com_con...icle&id=48&Itemid=53 Maker of several types of sealant.
If in doubt as to what type and where to apply the sealants/locking compounds, check with the shop manual. Another person to ask will be Larry Cavan at: www.cavanaughracing.com/
1982 GPZ1100 B2
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
General Dynamics/Convair 1983-1993
GLCM BGM-109 Tomahawk, AGM-129A Advanced Cruise Missile (ACM)
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Engine rebuild questions
08 Oct 2011 16:57 - 08 Oct 2011 17:00For reassembly, it's good to get heavy oil on the key surfaces like cam lobes, bearing faces, etc. There is some dedicated 'assembly lube" you can buy which is good, but we always used a 50-50 mix of STP oil treatment and motor oil. That gives you a thick, sticky oil that has a high concentration of ZDDP to protect things until the oil gets flowing.gwolever wrote: Cool. Thanks. I forgot to ask another question too:
Since this engine will be sitting in the garage this winter after I put it back together, what should I use to protect it from rusting internally?
1979 KZ-750 Twin
Last edit: 08 Oct 2011 17:00 by bountyhunter.
Please Log in or Create an account to join the conversation.
- bountyhunter
-
- Offline
- User
-

Registered
- Posts: 7245
- Thanks: 338
Re: Engine rebuild questions
08 Oct 2011 16:59My 750 twin came with strong sealant on the base gasket. It also calls out sealant on the rubber camshaft end plugs. I know there was a couple of other places I don't remember now.650ed wrote: Look at your Kawasaki factory service manual. It tells you those few spots where sealant is required, otherwise put on dry. One only area on my bike that I found the manual called for sealant is on 2 spots on the clutch cover gasket where the gasket covers the casting joints on the engine.
1979 KZ-750 Twin
Please Log in or Create an account to join the conversation.
- wireman
-
- Offline
- User
-

Registered
- The most interesting prick in the world
- Posts: 4736
- Thanks: 299
Re: Engine rebuild questions
08 Oct 2011 18:49
first thing you need to do is remove all silver paint from all engine parts,only suzuki engines need to be painted to keep them from vaporizing! :woohoo:
posting from deep under a non-descript barn in an undisclosed location southwest of Omaha.
Please Log in or Create an account to join the conversation.
- tybolt99
-
- Offline
- User
-

Registered
- From where KZs came
- Posts: 310
- Thanks: 3
Re: Engine rebuild questions
08 Oct 2011 20:20bountyhunter wrote:For reassembly, it's good to get heavy oil on the key surfaces like cam lobes, bearing faces, etc. There is some dedicated 'assembly lube" you can buy which is good, but we always used a 50-50 mix of STP oil treatment and motor oil. That gives you a thick, sticky oil that has a high concentration of ZDDP to protect things until the oil gets flowing.gwolever wrote: Cool. Thanks. I forgot to ask another question too:
Since this engine will be sitting in the garage this winter after I put it back together, what should I use to protect it from rusting internally?
Bel Ray. Good stuff.
[attachment:1]840-0800.jpeg[/attachment]
82 KZ750 H3
76 KZ900 A4
74 Z1A
73 Z1 (on the shelf)
84 ZN1300
Franklinton, NC
76 KZ900 A4
74 Z1A
73 Z1 (on the shelf)
84 ZN1300
Franklinton, NC
Please Log in or Create an account to join the conversation.
- gwolever
-
Topic Author
- Offline
- User
-

Registered
- Posts: 237
- Thanks: 8
Re: Engine rebuild questions
09 Oct 2011 00:28
Thanks for the input guys. That will be helpful come Monday when I start putting it all together
...and you're a funny guy wireman. That was a good one.
I wasn't going to paint, but when I decided to JB weld a couple of broken fins I decided to get the aluminum paint. I really like the way it turned out. I'm hoping the black, aluminum, and polished pieces look sharp when I add my black Jet-hot coated headers. Can't wait to get her all finished.
...and you're a funny guy wireman. That was a good one.
I wasn't going to paint, but when I decided to JB weld a couple of broken fins I decided to get the aluminum paint. I really like the way it turned out. I'm hoping the black, aluminum, and polished pieces look sharp when I add my black Jet-hot coated headers. Can't wait to get her all finished.
1982 KZ1000 CSR
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Engine rebuild questions
09 Oct 2011 00:41
Before resorting to JBWeld, would consider talking with a professional welder about repairing the broken fins.
Good Fortune!
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
