Tacho cable still freaking leaking

  • KZ1000inaus
  • KZ1000inaus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Luminous Red KZ1000 A2
  • Posts: 135
  • Thanks: 4

Tacho cable still freaking leaking

03 Aug 2012 02:58
#540424
ok so ive replace both seals and the whole cable and it's still leaking by dripping out of the engine and down the cable.
I have made sure the cable screws on square as i understand that can be a problem
I'm assuming the seals aren't good enough quality.
any ideas?

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Tacho cable still freaking leaking

03 Aug 2012 09:38 - 03 Aug 2012 09:44
#540445
Would guess their being an issue involving removal and/or installation of the inner seal that's supposed to prevent oil from escaping around the tach drive shaft.

Perhaps all remnants of the old inner seal weren't completely removed before installing the new seal.
Or maybe the new seal was damaged during installation. Or was improperly installed.

A dental pic is useful when dislodging and picking out all the remnants of an old encrusted, carbonized inner seal. Together with a bright light and magnification to look inside and inspect the interior of the tach housing to assure it's clean and clear before installing the new seal.

Or maybe the new o'ring was damaged during installation of the tach drive housing.

Tach drive should remain completely oil tight even without the cable attached.

Good Fortune! :)
1973 Z1
KZ900 LTD
Last edit: 03 Aug 2012 09:44 by Patton.

Please Log in or Create an account to join the conversation.

  • ramtough_63
  • ramtough_63's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 2560
  • Thanks: 136

Re: Tacho cable still freaking leaking

03 Aug 2012 09:57
#540448
Patton wrote: Would guess their being an issue involving removal and/or installation of the inner seal that's supposed to prevent oil from escaping around the tach drive shaft.

Perhaps all remnants of the old inner seal weren't completely removed before installing the new seal.
Or maybe the new seal was damaged during installation. Or was improperly installed.

A dental pic is useful when dislodging and picking out all the remnants of an old encrusted, carbonized inner seal. Together with a bright light and magnification to look inside and inspect the interior of the tach housing to assure it's clean and clear before installing the new seal.

AMEN on getting the old seal out my first attempt was a disaster! I even bought a different tach drive
not realizing I just didnt do a good enough job removing the old inner seal (thought I tore something up)
1978 KZ1000 A2
Thrown Together To Ride Til Winter
Facebook Page
Free Range Custom Art


1982/83 750R/GPZ
1984 Goldwing 1200 Interstate
1982 Yamahopper QT50
Previous
2 79 HD sporty XLH
02 HD FLSTS Heritage
60's HD Hummer
70's Honda 550 Four
70 Yamaha 100
and various enduros dirtbikes minibikes etc...

Please Log in or Create an account to join the conversation.

  • bluej58
  • bluej58's Avatar
  • Offline
  • User
  • User
    Registered
  • The chrome don't get you home
  • Posts: 2474
  • Thanks: 507

Re: Tacho cable still freaking leaking

03 Aug 2012 11:27 - 03 Aug 2012 11:29
#540461
Hey Craig, I'm guessing that you bought the seals at the same place I did and mine are working fine, so I hope it's just a case of you having to clean the old rubber out a little better, be careful not to scratch anything, a wood tooth pick might work .

The drag is that you have to take the valve cover off again :pinch:

Wipe and clean all the surfaces real good too, and apply a little Yammabond over the end plugs if you've got some handy.

If you use a sealant give it a day to cure before firing her up.

Good luck,JD
78 KZ1000 A2A
Last edit: 03 Aug 2012 11:29 by bluej58.

Please Log in or Create an account to join the conversation.

  • KZ1000inaus
  • KZ1000inaus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Luminous Red KZ1000 A2
  • Posts: 135
  • Thanks: 4

Re: Tacho cable still freaking leaking

04 Aug 2012 09:06
#540654
cheers for the advice.
I'll get another seal and make sure all the old one is out.

Please Log in or Create an account to join the conversation.

  • dfinnegan71
  • dfinnegan71's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 104
  • Thanks: 2

Re: Tacho cable still freaking leaking

07 Aug 2012 01:58
#541145
I have the same Freakin' problem. I changed it only about 300 miles ago and now leaking again. I was thinking of removing the tach drive and installing one of those block off plates. Anyone having luck with those?
1981 GPZ 550 mild custom

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Tacho cable still freaking leaking

07 Aug 2012 09:07 - 07 Aug 2012 09:08
#541164
It should not be leaking that quickly. Did you replace all 3 pieces that seal the tach drive? If not, I would suggest you do, as that is the best way to stop the leak. All 3 parts are still available from Kawasaki, so any dealer can get them for you. See highlighted parts below:

Attachment 0000_2012-08-07.jpg not found

1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 07 Aug 2012 09:08 by 650ed.

Please Log in or Create an account to join the conversation.

  • dfinnegan71
  • dfinnegan71's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 104
  • Thanks: 2

Re: Tacho cable still freaking leaking

07 Aug 2012 19:04
#541232
Oh boy, I seem to be missing out on the gasket # 11009. I changed the other two items but didn't even know I need that there gasket. That explains alot!
Thanks 650ed!
1981 GPZ 550 mild custom

Please Log in or Create an account to join the conversation.

  • KZ1000inaus
  • KZ1000inaus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Luminous Red KZ1000 A2
  • Posts: 135
  • Thanks: 4

Re: Tacho cable still freaking leaking

07 Aug 2012 19:08
#541234
650ed wrote: It should not be leaking that quickly. Did you replace all 3 pieces that seal the tach drive? If not, I would suggest you do, as that is the best way to stop the leak. All 3 parts are still available from Kawasaki, so any dealer can get them for you. See highlighted parts below:

[/attachment]
Oh it looks like I might be missing the 92065-103 as i don't recall ever seeing that one.
Does it sit in the end of the tacho cable?

Please Log in or Create an account to join the conversation.

  • KZ1000inaus
  • KZ1000inaus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Luminous Red KZ1000 A2
  • Posts: 135
  • Thanks: 4

Re: Tacho cable still freaking leaking

07 Aug 2012 19:10
#541236
dfinnegan71 wrote: Oh boy, I seem to be missing out on the gasket # 11009. I changed the other two items but didn't even know I need that there gasket. That explains alot!
Thanks 650ed!

haha me too!!
it must have been missing since the last owner..

Please Log in or Create an account to join the conversation.

  • 650ed
  • 650ed's Avatar
  • Offline
  • User
  • User
    Registered
  • Posts: 15334
  • Thanks: 2832

Re: Tacho cable still freaking leaking

07 Aug 2012 19:14
#541238
It's possible the old one was stuck in your cable connector, it is the last piece to go on before the cable is attached and they're pretty small. Here's a pic:

Attachment 0000b.JPG not found

1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)

Please Log in or Create an account to join the conversation.

  • KZ1000inaus
  • KZ1000inaus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Luminous Red KZ1000 A2
  • Posts: 135
  • Thanks: 4

Re: Tacho cable still freaking leaking

07 Aug 2012 19:32
#541240
ive just spoke to my local Z1 parts dealer come expert and he says it's very unlikely that the little missing gasket would stop it leasing as it's the other 2 that do that. he said he cant even remember ever selling one of those.
but he did ask me which way i'd put the other seal in and i said pointy end into engine (the way it looks like it should) which i'm told is the wrong way !
He said I've probably damaged it so i'm gonna get another today and fit it around the right way!!

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum