Engine refuses to fire

  • Ruminus
  • Ruminus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 25
  • Thanks: 0

Engine refuses to fire

16 Nov 2011 06:28
#488730
Hi all;

Bike: 1982 KZ-1000 LTD

So, a while back, I was riding home from work and my cam chain snapped on the freeway. Used a 1-piece chain to replace it, so I had to tear down the engine to remove the crank shaft and install the new chain. But, when I finished putting everything back together, she refuses to turn over. Here's what I've checked/tried so far:

*New plugs (old ones were a little gunked)

*Completely tore down/cleaned carbs

*Verified good spark on all 4 plugs, even tried swapping ignition coils to eliminate a 180 out possibility (I know, shouldn't be possible, but I'm trying everything).

*Timing was set exactly to book specs (i.e. exhaust cam sprocket arrow flush w/ block, intake cam arrow @ 44th cam chain pin while engine @ TDC on 1 and 4).

*Verified proper cam placement (exhaust on exhaust, intake on intake); at least I think so. The book I'm using says the cam that has its sprocket bolted on at the square outlined holes is the intake cam and the other one with no outline around the bolt holes is the exhaust cam. Is that right?

*Verified all cylinder compressions read good

*Something else I noted is that it only sounds like number 4 is trying to fire, but when it or one of the other cylinders does catch, I get a backfire out of the intake, and then only if I've spritzed it with some starter fluid. Also sounds as though the starter may be turning a little slower than it should, even with a fully charged battery.

*Made sure the bottom piston ring gap faced rear and the top piston ring gap faced front on reassembly.

Well, that's about it. I've got a bike that by all rights should turn over, but something is wrong, and I'm out of ideas. Any help is greatly appreciated.

Please Log in or Create an account to join the conversation.

  • Patton
  • Patton's Avatar
  • Offline
  • KZr Legend
  • KZr Legend
    Registered
  • Posts: 18564
  • Thanks: 2103

Re: Engine refuses to fire

16 Nov 2011 06:44
#488731
Ruminus wrote: ... The book I'm using says ....
If needed:
www.metrovationinc.com/christemple/kz.pdf

Good Fortune! :)
1973 Z1
KZ900 LTD
The following user(s) said Thank You: Ruminus

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Engine refuses to fire

16 Nov 2011 09:45 - 16 Nov 2011 10:18
#488741
I've got the same bike, and a FSM in my signature for download.
If the Compression is good, do you have #'s?
Maybe the two wires for the Ignition coils from the Ignitiors are crossed. This is the Green and the Black signal wires, the Reds are the power. Maybe try moving them? Swap the two to the other coil?

The FSM will tell you the cam gear reference, then you can check it against what you have in the other manual.





If you remove the valve cover, remember to take out the Tensioner Cross wedge. Do Not reinstall the Valve Cover With the Cross Wedge Installed.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Last edit: 16 Nov 2011 10:18 by Motor Head.
The following user(s) said Thank You: Ruminus

Please Log in or Create an account to join the conversation.

  • Ruminus
  • Ruminus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 25
  • Thanks: 0

Re: Engine refuses to fire

16 Nov 2011 10:02 - 16 Nov 2011 11:05
#488745
I don't have numbers yet on the compression. My brother in law has the gauge, and I haven't had a chance to use it, but with the plug out, you can't keep a thumb over the hole, it quite forcefully shoves it away with the air. I know, not scientific, and it'll be better once I can gauge it.
As far as the coil leads, that was one of my first thoughts. Green goes to the right and black to the left at the moment. Book said that was right and I seem to remember that's how it was before I yanked the coils. Hopefully the fix is that simple. : (
*Edit: One other note. These are all-but-new Dynatek coils, so I'm pretty much ruling out a coil failure, especially since I'm getting a good spark.
Last edit: 16 Nov 2011 11:05 by Ruminus.

Please Log in or Create an account to join the conversation.

  • Ruminus
  • Ruminus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 25
  • Thanks: 0

Re: Engine refuses to fire

16 Nov 2011 10:21
#488746
Also, thanks to both of you guys for the service manual links. They've been much more in-depth than the manual I've been using. I checked the electrical schematic, and the coils are properly wired. As far as the cam sprocket bolts, I'll have to take a look when I get a minute to pull the valve cover off again, but I think that I've got those set correctly as well. <sigh>

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Engine refuses to fire

16 Nov 2011 10:28
#488747
How about the Valve Clearances? Did you have to get your head rebuilt? Were valves bent when the chain snapped? If you haven't checked those values, I would, also the Gauge Compression test.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • Ruminus
  • Ruminus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 25
  • Thanks: 0

Re: Engine refuses to fire

16 Nov 2011 10:32 - 16 Nov 2011 10:35
#488749
#2 Intake was a little tweaked, but I managed to tap it back straight on a block. I had just replaced the shims a month before the "Ooh, what was that noise!? Hey, why aren't I going anywhere?" moment, and when I checked, they all still had good clearance (no feelers, unfortunately, just using the old "It rotates in the sleeve freely" trick). And no, I didn't get the head rebuilt.
Last edit: 16 Nov 2011 10:35 by Ruminus. Reason: Add a comment

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Engine refuses to fire

16 Nov 2011 10:42
#488752
Ruminus wrote: #2 Intake was a little tweaked, but I managed to tap it back straight on a block. I had just replaced the shims a month before the "Ooh, what was that noise!? Hey, why aren't I going anywhere?" moment, and when I checked, they all still had good clearance (no feelers, unfortunately, just using the old "It rotates in the sleeve freely" trick). And no, I didn't get the head rebuilt.
Uh, Back firing out the #2 Cylinder Carb? You Straightened the Valve on a block of wood?
Did you at least do a "Solvent Check" to see if the valves were sealing? That's filling the port with a Solvent and looking to see if the fluid runs out around the valve.
Sounds like you need to do a Leak Down Test, do you know how, or what that is?
The Probability of the head needing work is High.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • Ruminus
  • Ruminus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 25
  • Thanks: 0

Re: Engine refuses to fire

16 Nov 2011 10:47
#488753
No, backfiring out of 1 and 3 mainly, but all 4 have done it. And yes, I did a solvent test, it just sat there on all 8 valves. Leak down, no, I haven't done that (nor do I know what it is, sadly, though I might have an idea).

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Engine refuses to fire

16 Nov 2011 10:51
#488754
Well if the solvent test showed that they held, then hopefully it will be alright. A Compression test with your friends gauge would be a good Idea.
back on the Coils, 1-4, then 2-3, nothing wrong with where the secondary wires are?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

  • Ruminus
  • Ruminus's Avatar Topic Author
  • Offline
  • User
  • User
    Registered
  • Posts: 25
  • Thanks: 0

Re: Engine refuses to fire

16 Nov 2011 10:56
#488755
Left hand coil is fed by black and red and goes to 1 (forward boot) and 4 (aft boot). Right hand coil is fed by green and red and goes to 2 (forward boot) and 3 (aft boot). The Dynateks have laterally mounted ports inline on the outside of the coil, as opposed to the OEM coils, which are both aft mounted.

Please Log in or Create an account to join the conversation.

  • Motor Head
  • Motor Head's Avatar
  • Offline
  • User
  • User
    Registered
  • FIX UP YOUR BIKE RIGHT AND CHEAP
  • Posts: 5137
  • Thanks: 393

Re: Engine refuses to fire

16 Nov 2011 11:03
#488758
Ruminus wrote: No, backfiring out of 1 and 3 mainly, but all 4 have done it. And yes, I did a solvent test, it just sat there on all 8 valves. Leak down, no, I haven't done that (nor do I know what it is, sadly, though I might have an idea).
A leak Down Test is putting each cylinder at Top Dead Center (TDC) and using a regulated compressed air supply to put 100psi into the cylinder, there is a gauge to show the incoming pressure and the pressure held. If much of a leak, above 25%, then listening to the Intake, Exhaust, oil cap, etc will tell you where its going. Then a small addition of oil to the air will help briefly to close the rings to see how bad the leakage there was.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf

Please Log in or Create an account to join the conversation.

Moderators: Street Fighter LTD
Powered by Kunena Forum