Engine refuses to fire
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Engine refuses to fire
16 Nov 2011 13:52 - 16 Nov 2011 13:54
When the cam chain breaks, don't the closed valves stay closed?
Good Fortune!
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 16 Nov 2011 13:54 by Patton.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Engine refuses to fire
16 Nov 2011 14:17When the Chain Breaks or otherwise comes out of time/ Slips, jumps teeth, It is a Lottery Victory If an Interference engine doesn't at Least bend the valves. Many motors try to Split the Atom when they loose time.Patton wrote: When the cam chain breaks, don't the closed valves stay closed?
Good Fortune!
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- elfmagic17
-
- Offline
- User
-

Registered
- Posts: 334
- Thanks: 24
Re: Engine refuses to fire
16 Nov 2011 14:49Ruminus wrote: #2 Intake was a little tweaked, but I managed to tap it back straight on a block. I had just replaced the shims a month before the "Ooh, what was that noise!? Hey, why aren't I going anywhere?" moment, and when I checked, they all still had good clearance (no feelers, unfortunately, just using the old "It rotates in the sleeve freely" trick). And no, I didn't get the head rebuilt.
Not to sure I would trust a valve that was bent, it could be fractured and cause major damage if it comes apart. I'm with them, It may have at least on or two bent valves. Only think of two causes of back-firing out of intake, bad timing(cam or Ignition) or bent/burnt valves. Leak test the cylinders with pressure with both valves "closed" only should see a max of about 10% leakage. Any more would indicate a pretty serious leak.
Kenny Hicks
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
74 Honda CB550
75 Honda CB360 (runs and rides good but not a show bike)
77 KZ650B1 (Runs Great, but needs painted and a little work.)
Please Log in or Create an account to join the conversation.
- baldy110
-
- Offline
- User
-

Registered
- Posts: 2272
- Thanks: 512
Re: Engine refuses to fire
17 Nov 2011 00:21 - 17 Nov 2011 00:22
When the timing chain breaks the cams stops where they are but the pistons keep moving. So when a valve is open and the piston comes up it slams into the valve bending it. Now the real fun is when the chain breaks when your revving the snot out of it, like a freeway entrance ramp, you can kiss the top end goodby.
I have worked on a lot of interference engines where the cam chain broke and I have never found one without a bent valve.
I have worked on a lot of interference engines where the cam chain broke and I have never found one without a bent valve.
Last edit: 17 Nov 2011 00:22 by baldy110.
Please Log in or Create an account to join the conversation.
- 650ed
-
- Offline
- User
-

Registered
- Posts: 15334
- Thanks: 2832
Re: Engine refuses to fire
17 Nov 2011 00:37 - 17 Nov 2011 00:43baldy110 wrote: When the timing chain breaks the cams stops where they are but the pistons keep moving. So when a valve is open and the piston comes up it slams into the valve bending it. Now the real fun is when the chain breaks when your revving the snot out of it, like a freeway entrance ramp, you can kiss the top end goodby.
I have worked on a lot of interference engines where the cam chain broke and I have never found one without a bent valve.
Right. If a guy was driving along at a moderate speed, let's say 4,000 rpm (that's about 66 revolutions per second) and the cam chain broke the valves stop in place and even if the engine miraculously stops in one second (doubtful) the pistons are going to smack whichever valves are open (gonna be at least one intake and one exhaust) 66 times. Ouch!! Ed
Another thought comes to mind.... when the piston smacks the valve head wouldn't the force be transferred through the valve stem to the cam? And unless the valve stem happened to be dead center on the cam lobe might this then turn the cam which would open another valve and cause it to be smacked by its piston? It would be interesting to see a video of such an event. Ed
1977 KZ650-C1 Original Owner - Stock (with additional invisible FIAMM horn)
Last edit: 17 Nov 2011 00:43 by 650ed.
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: Engine refuses to fire
17 Nov 2011 08:42
Bent valves...
Look again at the piston domes and valve faces in the head combustion areas.
Should have a nice clear indication that the pistons whacked into a valve... :pinch:
Look again at the piston domes and valve faces in the head combustion areas.
Should have a nice clear indication that the pistons whacked into a valve... :pinch:
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
17 Nov 2011 10:39Well, there's a good bit of carbon build up, but would you believe not a scratch on anything that would indicate an impact? Even the #2 intake that I know was bent doesn't show a mark on the piston or valve. So, I guess it's all about how that compression gauge reads when I can get my hands on it.Old Man Rock wrote: Bent valves...
Look again at the piston domes and valve faces in the head combustion areas.
Should have a nice clear indication that the pistons whacked into a valve... :pinch:
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
17 Nov 2011 10:39650ed wrote:baldy110 wrote: When the timing chain breaks the cams stops where they are but the pistons keep moving. So when a valve is open and the piston comes up it slams into the valve bending it. Now the real fun is when the chain breaks when your revving the snot out of it, like a freeway entrance ramp, you can kiss the top end goodby.
I have worked on a lot of interference engines where the cam chain broke and I have never found one without a bent valve.
Right. If a guy was driving along at a moderate speed, let's say 4,000 rpm (that's about 66 revolutions per second) and the cam chain broke the valves stop in place and even if the engine miraculously stops in one second (doubtful) the pistons are going to smack whichever valves are open (gonna be at least one intake and one exhaust) 66 times. Ouch!! Ed
Another thought comes to mind.... when the piston smacks the valve head wouldn't the force be transferred through the valve stem to the cam? And unless the valve stem happened to be dead center on the cam lobe might this then turn the cam which would open another valve and cause it to be smacked by its piston? It would be interesting to see a video of such an event. Ed
That's just plain depressing.
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
17 Nov 2011 10:41Patton wrote: Ignition timing might be 180° off due to incorrect assembly.
Would verify that the rotor pointer (if oem ignition) or embedded magnet (if Dyna-S rotor) is at the left hand module/pickup when the 1/4 F mark is aligned with the permanet case timing mark.
Ignore the T mark relative to ignition timing.
Where ignition timing is correct (given proper cam timing, spark and compression), starting fluid should produce momentary engine running.
Good Fortune!
I checked the index marks again, everything is where it should be. And yes, the starter fluid not producing anything but a backfire pop has me puzzled, too.
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
17 Nov 2011 10:44 - 17 Nov 2011 10:54Old Man Rock wrote: Since you mentioned she rotates fully (manually we hope) and timing does in fact end up at TDC correct pins/lobe alignments to head deck... Doesn't seem your valves where bent so even with lower then spec compression, if all other was good spec she should fire.
Insure all kill switch or starter interlocks (kick stand switch) that may be on this model are in fact not active (killing the engine start).
Back fires out intakes sounds as though coils/sparkies on wrong cylinders but doubtful from what you have written. As others have replied insure this is correct from ignition plate wiring to coils to sparkies. Insure engine case is grounded at same potential as battery ground.
With a Fully charged "Good" battery (note I said good), should kick over relatively easy. Now that doesn't mean you can sit there for a couple minutes of constant starter energizing and not drain the battery. Again, insure engine case/frame grounding and charging system component grounding is to spec.
Outside of that... Warning Will Robinson Flag came on with the following...
"*Completely tore down/cleaned carbs".... Start There....
Good luck and keep at it, you'll find it...
The battery is brand new, except for the cranking I've been doing on it trying to souse this issue. I got a new one as the old one had been giving me problems and when the bike died on the road, I assumed it was the culprit. At least it was a warranty exchange and didn't cost me anything, but I so want to log some miles on it before I kill it with all this discharge/charge stuff. :lol: As far as kill switches, there's no kickstand switch, and even if there was, she's on the center stand and the k/s is up. The kill switch on the handlebars is also the starter switch, so if you press the starter, it comes out of "kill" position.
Your grounding idea is a good one though. The battery ground connector is a bit iffy, so I'm going to replace that (hopefully today). The ground at the block is clean and solid, so at least one end is good; that has to count for something, right?
Oh, and I only tore down/cleaned the carbs when it was readily apparent something was amiss. #2 and #3 plugs were dry even after trying to turn it over a while, so I was dearly hoping it was just a fuel supply issue.
Last edit: 17 Nov 2011 10:54 by Ruminus.
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
17 Nov 2011 10:48The ignition advancer has an index slot at the back side where it mates to the crankshaft, so it shouldn't be possible for it to be 180 out. I took it apart thinking the exact same thing and was unable to come up with a way to put it in backwards, even if I wanted to. :laugh:Motor Head wrote: More on Pattons Theory,
Is it possible that the Ignition Advancer has been Reassembled 180 out? Making the 1-4 marks show when its at 2-3?
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
17 Nov 2011 10:51Yes, that is how everything is set up, though my engine doesn't look quite that good. :blush:Patton wrote:Ruminus wrote: Left hand coil is fed by black and red and goes to 1 (forward boot) and 4 (aft boot). Right hand coil is fed by green and red and goes to 2 (forward boot) and 3 (aft boot)....
Just to confirm ---
Left hand coil is attached to the two outside spark plugs;
Right hand coil is attached to the two inside spark plugs.
Good Fortune!
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
