Engine refuses to fire
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
16 Nov 2011 11:05Motor Head wrote: A leak Down Test is putting each cylinder at Top Dead Center (TDC) and using a regulated compressed air supply to put 100psi into the cylinder, there is a gauge to show the incoming pressure and the pressure held. If much of a leak, above 25%, then listening to the Intake, Exhaust, oil cap, etc will tell you where its going. Then a small addition of oil to the air will help briefly to close the rings to see how bad the leakage there was.
Guessing that's mainly a next step if compression is horrible once I get a gauge on there?
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Engine refuses to fire
16 Nov 2011 11:07
Yes, and also the two other things inside the Valve cover, Timing and clearances.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
16 Nov 2011 11:13
And if I'm seeing this right, once I can get a feeler in there, I'm looking for something in the .0050-.0070 range on clearance and about 170-180 psi cranking compression?
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Engine refuses to fire
16 Nov 2011 11:20
About .003-.004 Thousandths of an inch. Some set the IN slightly tighter than the EX, EX at .004" is good I think, and IN at .003" but that's basically if you have a shim selection to do that.
Cranking Compression will very with Altitude, so if you are at Sea Level and the motor was rebuilt, and just broken in, the those 180psi #'s would be Great. But in Reality, on your motor, 120-150psi is probably more like it, nothing below 100psi.
Cranking Compression will very with Altitude, so if you are at Sea Level and the motor was rebuilt, and just broken in, the those 180psi #'s would be Great. But in Reality, on your motor, 120-150psi is probably more like it, nothing below 100psi.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
The following user(s) said Thank You: Ruminus
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
16 Nov 2011 11:23
I have a few shims floating around, so I might be able to cook something up in that neighborhood. Also, I'm at 4,300 ft here in the Salt Lake area, so I'll take anything over 100 until I can get some new guts. It's all on a tight budget, unfortunately. I'm lucky my wife allows me the obsession as much as she does. :blush:
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Engine refuses to fire
16 Nov 2011 11:27
@ 4300' you will see a bit of a drop. I get about 125-130psi on mine @ 6200'.
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- Ruminus
-
Topic Author
- Offline
- User
-

Registered
- Posts: 25
- Thanks: 0
Re: Engine refuses to fire
16 Nov 2011 11:31
Well, thank you for all the help so far.
I'll be sure to update the thread as I get any results, either in measurements or (hopefully) a successful start. :huh:
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Engine refuses to fire
16 Nov 2011 12:05Ruminus wrote: Left hand coil is fed by black and red and goes to 1 (forward boot) and 4 (aft boot). Right hand coil is fed by green and red and goes to 2 (forward boot) and 3 (aft boot)....
Just to confirm ---
Left hand coil is attached to the two outside spark plugs;
Right hand coil is attached to the two inside spark plugs.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Old Man Rock
-
- Offline
- User
-

Registered
- Posts: 6071
- Thanks: 225
Re: Engine refuses to fire
16 Nov 2011 12:27 - 16 Nov 2011 12:30
Since you mentioned she rotates fully (manually we hope) and timing does in fact end up at TDC correct pins/lobe alignments to head deck... Doesn't seem your valves where bent so even with lower then spec compression, if all other was good spec she should fire.
Insure all kill switch or starter interlocks (kick stand switch) that may be on this model are in fact not active (killing the engine start).
Back fires out intakes sounds as though coils/sparkies on wrong cylinders but doubtful from what you have written. As others have replied insure this is correct from ignition plate wiring to coils to sparkies. Insure engine case is grounded at same potential as battery ground.
With a Fully charged "Good" battery (note I said good
), should kick over relatively easy. Now that doesn't mean you can sit there for a couple minutes of constant starter energizing and not drain the battery. Again, insure engine case/frame grounding and charging system component grounding is to spec.
Outside of that... Warning Will Robinson Flag came on with the following...
"*Completely tore down/cleaned carbs".... Start There....
Good luck and keep at it, you'll find it...
Insure all kill switch or starter interlocks (kick stand switch) that may be on this model are in fact not active (killing the engine start).
Back fires out intakes sounds as though coils/sparkies on wrong cylinders but doubtful from what you have written. As others have replied insure this is correct from ignition plate wiring to coils to sparkies. Insure engine case is grounded at same potential as battery ground.
With a Fully charged "Good" battery (note I said good
Outside of that... Warning Will Robinson Flag came on with the following...
"*Completely tore down/cleaned carbs".... Start There....
Good luck and keep at it, you'll find it...
1976 KZ900-A4
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
MTC 1075cc.
Camshafts: Kawi GPZ-1100 .375 lift
Head: P&P via Larry Cavanaugh
ZX636 suspension
MIKUNI, RS-34'S...
Kerker 4-1, 1.5" comp baffle.
Dyna-S E.I.
Earls 10 row Oil Cooler
Acewell 2802 Series Speedo/Tach
Innovate LC1 Wideband 02 AFR meter
Phoenix, Az
Last edit: 16 Nov 2011 12:30 by Old Man Rock.
Please Log in or Create an account to join the conversation.
- Patton
-
- Offline
- KZr Legend
-

Registered
- Posts: 18564
- Thanks: 2103
Re: Engine refuses to fire
16 Nov 2011 12:44 - 16 Nov 2011 12:49
Ignition timing might be 180° off due to incorrect assembly.
Would verify that the rotor pointer (if oem ignition) or embedded magnet (if Dyna-S rotor) is at the left hand module/pickup when the 1/4 F mark is aligned with the permanet case timing mark.
Ignore the T mark relative to ignition timing.
Where ignition timing is correct (given proper cam timing, spark and compression), starting fluid should produce momentary engine running.
Good Fortune!
Would verify that the rotor pointer (if oem ignition) or embedded magnet (if Dyna-S rotor) is at the left hand module/pickup when the 1/4 F mark is aligned with the permanet case timing mark.
Ignore the T mark relative to ignition timing.
Where ignition timing is correct (given proper cam timing, spark and compression), starting fluid should produce momentary engine running.
Good Fortune!
1973 Z1
KZ900 LTD
KZ900 LTD
Last edit: 16 Nov 2011 12:49 by Patton.
Please Log in or Create an account to join the conversation.
- Motor Head
-
- Offline
- User
-

Registered
- FIX UP YOUR BIKE RIGHT AND CHEAP
- Posts: 5137
- Thanks: 393
Re: Engine refuses to fire
16 Nov 2011 13:46
More on Pattons Theory,
Is it possible that the Ignition Advancer has been Reassembled 180 out? Making the 1-4 marks show when its at 2-3?
Is it possible that the Ignition Advancer has been Reassembled 180 out? Making the 1-4 marks show when its at 2-3?
1982 KZ1000LTD K2 Vance & Hines 4-1 ACCEL COILS Added Vetter fairing & Bags. FOX Racing rear Shocks, Braced Swing-arm, Fork Brace, Progressive Fork Springs RT Gold Emulators, APE Valve Springs, 1166 Big Bore kit, RS34's, GPZ cams.
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
1980 KZ550LTD C1 Stock SOLD Miss it
1979 MAZDA RX7 in the works, 13B 6 port built/ light flywheel/ 48 DCO Weber LUV IT! Street Legal Go Cart!
1982 KZ1100 A-2 Shaft just bought it in pieces form 1st owner: Now Running Great! SOLD
1990 Concours 1000 Project bike rough body work: Now Running & Riding!
www.kz1000r.com/downloads/Kawasaki%20KZ1...Service%20Manual.pdf
Please Log in or Create an account to join the conversation.
- baldy110
-
- Offline
- User
-

Registered
- Posts: 2272
- Thanks: 512
Re: Engine refuses to fire
16 Nov 2011 13:48
If the cam chain broke while the engine was running you bent a valve period. These are all interference engines. I would make sure none of the valves are bent. just because you are getting compression does not mean a valve is not bent.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD
